View RM21WTP-CP12_8799642.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 general-purpose multi-contact circular waterproof connectors rm-w series 2006.1 overview high performance waterproof circular connectors and cable assemblies used in variety of applications requiring high reliability, ease of assembly and small size. features 1. variety of types plugs : available in 3 types - straight / long back shell, straight / short back shell, right angle back shell. receptacles : waterproof types with front, back or flange panel mounting. all types with 2, 3, 4, 8, 10, 12, 15, 20, 31, 40, 55 contacts. contacts in 2 plating types: gold or silver. 2. dust and water protection when fully mated, the connector meet requirements of ip67 (48 hours at depth of 1.8 m) (single-body waterproof receptacles also meet requirements of ip67.) 3. cable exit in 360 directions the right-angle plugs permit exiting of the cable over a 360-degree range in any direction. applications base stations, factory automation equipment, robotic equipment, exploration and construction equipment, research instrumentation, variety of industrial and measuring instruments. any other applications requiring high reliability waterproof circular connectors. ?23 40 41 cable 360 360 cable exit plug _ right angle plug _ straight ?21.5 ?23 57 ?21.5 48 short backshell long backshell the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
2 2 m ? max.(2, 3, 4 pos.) 4 m ? max.(8, 10, 12 pos.) 1000 m ? min no flashover or insulation breakdown. no electrical discontinuity for 10s max. no electrical discontinuity for 10s max. 4 m ? max.(2, 3, 4 pos.) 8 m ? max.(8, 10, 12 pos.) insulation resistance: 100 m ? min. insulation resistance: 100 m ? min. (dray state) 0when mated with corresponding connector. 1a dc 500v dc 1800v ac/one minute (2 pos.) 2000v ac/one minute (3 pos.) 1500v ac/one minute (4, 8 pos.) 1000v ac/one minute (10, 12 pos.) frequency: 10 to 55hz, single amplitude of 0.75mm,for 3 hours in 3 axis. acceleration of 490m/s 2 , 11ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. 2000 cycles temperature : -55? ? room temperature ? +85? ? room temperature time : 30 ? 10 to 15 ? 30 ? 10 to 15 (minutes) 5 cycles 96 hours at temperature 0f 40? and humidity 0f 90% to 95%. complete dust protection. no water penetration when submerged for 48 hours at the depth of 1.8 meter. 1. contact resistance 2. insulation resistance 3. withstanding voltage 4. vibration 5. shock 6. durability (insertion/withdrawal) 7. temperature cycle 8. humidity 9. water / dust protection rating voltage rating current rating operating temperature range (note 1) storage temperature range (note 2) 600v ac, 840v dc (2 pos.) 500v ac, 700v dc (3, 4, 8 pos.) 350v ac, 490v dc (10 pos.) 350v ac, 490v dc (12 pos.) 10a (2, 3, 4 pos.) 5a (8, 10, 12 pos.) -25? to +85? -25? to +85? product specifications (rm15wt size products) materials characteristic specification conditions body insulator contacts gasket zinc alloy, brass, pliable pvc diallyl phthalate, pbt brass, phosphor bronze, or copper alloy sir (black or red), or nbr (gray) chrome plated or nickel plated color: black silver plated or gold plated color: black or red (sir), color: gray (nbr) ------------------- ul94v-0 ------------------- ------------------- item material finish remarks note 1: includes temperature rise caused by the current flow. note 2: the term storage refers to products stored for long period of time prior to mounting and use. operating temperature r ange and humidity range note 2: covers non-conducting condition of installed connectors in storage, shipment or during transportation. note: do not mix different contact plating. ordering information rm 15 w t p * * * * - 2 p ( * * * * ) 1 2 1 3 4 5 6 7 series name : rm-w shell size lock type t : screw lock connector type p : plug r : receptacle 1 number of contacts contact type p : male contact s : female contact plating (71) : silver plated (72) : gold plated 5 6 2 3 4 7 the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
3 plugs - straight, long back shell applicable strain reliefs external cable clamp + internal, self-tightening internal, self tightening 109-1734-5- part number cl no. number of contacts weight rohs rm15wtpza-2p() rm15wtpza-3p( 72 ) rm15wtpza-4p() rm15wtpza-8p() rm15wtpza-10p() rm15wtpza-12p() 2 43g yes 109-1602-4- 72 109-1735-8- 109-1736-0- 109-1737-3- 109-1738-6- 3 4 8 10 12 45g 44g 43g 44g 44g m191 m200.75 wrench opening dimension of 18 mm ?15.2 45.3 ?21.5 2 1 3 part number cl no. number of contacts weight rohs rm15wtpza-2s() rm15wtpza-3s() rm15wtpza-4s() rm15wtpza-8s() rm15wtpza-10s() rm15wtpza-12s() 109-1729-5- 2 45g yes 109-1601-1- 109-1730-4- 109-1731-7- 109-1732-0- 109-1733-2- 3 4 8 10 45g 12 47g 45g 45g 45g (shown one example) (shown one example) wrench opening dimension of 21 mm ?23 m200.75 17.5 drive screw(2) a wrench opening dimension of 21 mm ?23 m200.75 8 a rm15wtpza-10s(71) jr16wcc-10(72) jr16wcca-10(72) part number cl no. a weight rohs jr16wcc-4(72) jr16wcc-6(72) jr16wcc-8(72) 114-2052-6-72 4 17.5g 114-2053-9-72 114-2054-1-72 6 8 17.5g 17.5g part number cl no. a weight rohs jr16wcc-10(72) jr16wcc-11(72) jr16wcc-12(72) 114-2055-4-72 10 17.5g yes 114-2154-6-72 114-2056-7-72 11 12 17.5g 17.5g part number cl no. a weight rohs jr16wcca-4(72) jr16wcca-6(72) notes : 1. cable jacket diameter:use a 0.2mm 2. when using the self-tightening strain relief verify the cable pull force requirements. jr16wcca-8(72) 114-2076-4-72 114-2077-7-72 114-2078-0-72 4 16g 6 16g 8 16g yes part number cl no. a weight rohs jr16wcca-10(72) jr16wcca-11(72) jr16wcca-12(72) 114-2079-2-72 114-2155-9-72 114-2080-1-72 10 16g 11 16g 12 16g yes [specification number] (**), -** (71) : silver plated contacts (72) : gold plated contacts (shown one example) yes the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
4 109-1616-9- part number cl no. number of contacts weight rohs rm15wtpz-2p() rm15wtpz-3p() rm15wtpz-4p() rm15wtpz-8p() rm15wtpz-10p() rm15wtpz-12p() 2 32g yes 109-1622-1- 109-1617-1- 109-1618-4- 109-1619-7- 109-1620-6- 3 4 8 10 12 34g 33g 32g 33g 33g m191 m160.75 wrench opening dimension of 18 mm ?15.2 36.3 ?21.5 1 3 2 part number cl no. number of contacts weight rohs rm15wtpz-2s() rm15wtpz-3s() rm15wtpz-4s() rm15wtpz-8s() rm15wtpz-10s() rm15wtpz-12s() 109-1611-5- 2 34g yes 109-1621-9- 109-1612-8- 109-1613-0- 109-1614-3- 109-1615-6- 3 4 8 10 12 36g 34g 34g 34g 34g 17 m160.75 wrench opening dimension of 17 mm ?20 a drive screw(2) 7.5 m160.75 wrench opening dimension of 17 mm ?20 a rm15wtpz-10s jr13wcc-10(72) jr13wcca-10(72) part number cl no. a weight rohs jr13wcc-4(72) jr13wcc-5(72) jr13wcc-6(72) 114-2045-0-72 4 17g yes 114-2046-3-72 114-2047-6-72 5 17g 6 17g part number cl no. a weight rohs jr13wcc-7(72) jr13wcc-8(72) jr13wcc-9(72) jr13wcc-10(72) 114-2048-9-72 7 17g yes 114-2049-1-72 114-2050-0-72 114-2051-3-72 8 17g 9 17g 10 17g part number cl no. a weight rohs jr13wcca-4(72) jr13wcca-5(72) notes : 1. cable jacket diameter: use a 0.2mm 2. when using the self-tightening strain relief verify the cable pull force requirements. jr13wcca-6(72) 114-2069-9-72 114-2070-8-72 114-2071-0-72 4 12g 5 12g 6 12g yes part number cl no. a weight rohs jr13wcca-7(72) jr13wcca-8(72) jr13wcca-9(72) jr13wcca-10(72) 114-2072-3-72 114-2073-6-72 114-2074-9-72 114-2075-1-72 7 12g 8 12g 9 12g 10 12g yes plugs - straight, short back shell applicable strain reliefs external cable clamp + internal, self-tightening internal, self tightening [specification number] (**), -** (71) : silver plated contacts (72) : gold plated contacts (shown one example) (shown one example) (shown one example) the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
5 notes : 1 gasket material: nbr, body plating: nickel 2 recommended set screw tightening torque: 0.2 to 0.3 n?m. hrs recommended tool: pb205/1.27(cl 150-0066-3) 109-0997-9-71 part number cl no. number of contacts weight rohs rm15wtlp-12p(71) 12 62.3g yes m191 m160.75 wrench opening dimension of 21.8 mm set screw(2) hexagonal hole opposite side 1.27 mm (1.27hex) ?15.2 19.15 39.5 ?23 part number cl no. number of contacts weight rohs rm15wtlp-10s(71) 109-0999-4-71 10 63.1g yes 17 m160.75 wrench opening dimension of 17 mm ?20 a drive screw(2) 7.5 m160.75 wrench opening dimension of 17 mm ?20 a rm15wtlp-10s jr13wcc-10 (72) jr13wcca-10(72) part number cl no. a weight rohs jr13wcc-4(72) jr13wcc-5(72) jr13wcc-6(72) 114-2045-0-72 4 17g yes 114-2046-3-72 114-2047-6-72 5 17g 6 17g part number cl no. a weight rohs jr13wcc-7(72) jr13wcc-8(72) jr13wcc-9(72) jr13wcc-10(72) 114-2048-9-72 7 17g yes 114-2049-1-72 114-2050-0-72 114-2051-3-72 817g 917g 10 17g part number cl no. a weight rohs jr13wcca-4(72) jr13wcca-5(72) notes : 1 cable jacket diameter: use a 0.2mm 2 when using the self-tightening strain relief verify the cable pull force requirements. jr13wcca-6(72) 114-2069-9-72 114-2070-8-72 114-2071-0-72 4 12g 5 12g 6 12g yes part number cl no. a weight rohs jr13wcca-7(72) jr13wcca-8(72) jr13wcca-9(72) jr13wcca-10(72) 114-2072-3-72 114-2073-6-72 114-2074-9-72 114-2075-1-72 712g 812g 912g 10 12g yes plugs - right angle applicable strain reliefs external cable clamp + internal, self-tightening internal, self tightening (shown one example) (shown one example) (shown one example) the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
6 receptacles front panel mount rear panel mount notes : recommended nut tightening torque: 3n?m notes : recommended nut tightening torque: 3n?m 109-1631-2- 109-1632-5- 109-1633-8- 109-1634-0- 109-1635-3- 109-1636-6- 109-1637-9- cl no. 109-1638-1- 109-1639-4- 109-1640-3- 109-1641-6- 109-1642-9- part number cl no. number of contacts weight rohs a 13g yes 21 15g 22.1 14g 21 13g 20.65 14g 20.65 14g 20.65 15g yes weight rohs 17g 15g 15g 15g 15g rm15wtrz-2p() rm15wtrz-3p() rm15wtrz-4p() rm15wtrz-8p() rm15wtrz-10p() rm15wtrz-12p() rm15wtrz-2s() part number rm15wtrz-3s() rm15wtrz-4s() rm15wtrz-8s() rm15wtrz-10s() rm15wtrz-12s() 2 3 4 8 10 12 2 21.75 number of contacts a 3 22.1 4 21.75 8 21.6 10 21.6 12 21.6 2 1 2 1 wrench opening dimension of 18 mm a 9 6 2 m191 ?22 13 a 2 6.5 m191 24(hex) m211 ?27 rm15wtrz-10s(71) rm15wtrza-10s(71) 109-1651-0- 109-1652-2- 109-1653-5- 109-1654-8- 109-1655-0- 109-1656-3- 109-1657-6- cl no. 109-1658-9- 109-1659-1- 109-1660-0- 109-1661-3- 109-1662-6- part number cl no. number of contacts weight rohs a 22g yes 21 24g 22.1 23g 21 22g 20.65 23g 20.65 23g 20.65 24g yes weight rohs 26g 24g 24g 24g 24g rm15wtrza-2p() rm15wtrza-3p() rm15wtrza-4p() rm15wtrza-8p() rm15wtrza-10 p() rm15wtrza-12 p() rm15wtrza-2s() part number rm15wtrza-3s() rm15wtrza-4s() rm15wtrza-8s() rm15wtrza-10 s() rm15wtrza-12 s() 2 3 4 8 10 12 2 21.75 number of contacts a 3 22.1 4 21.75 8 21.6 10 21.6 12 21.6 [specification number] (**), -** (71) : silver plated contacts (72) : gold plated contacts [specification number] (**), -** (71) : silver plated contacts (72) : gold plated contacts (shown one example) (shown one example) the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
7 number of contacts notes : 1. screw size: m3 2. recommended nut tightening torque : 0.3 to 0.35n?m 109-1671-7- 109-1672-0- 109-1673-2- 109-1674-5- 109-1675-8- 109-1676-0- part number cl no. number of contacts weight rohs a 19g yes 21 21g 22.1 20g 21 19g 20.65 20g 20.65 20g 20.65 rm15wtrzb-2p() rm15wtrzb-3p() rm15wtrzb-4p() rm15wtrzb-8p() rm15wtrzb-10p() rm15wtrzb-12p() 2 3 4 8 10 12 2 3 2 3 1 1 28 2 m191 6 ?19 ?1.9 9 a 4-?3.6 20.6 20.6 28 2 3 2 3 1 1 28 2 m191 6 ?19 ?1.9 9 a 4-?3.6 20.6 20.6 28 rm15wtrzb-10s(71) jr15wtrzb-10pa(71) notes : 1. screw size: m3 2. recommended nut tightening torque : 0.3 to 0.35n?m 109-1692-7 109-1693-0 109-1694-2 cl no. 109-1695-5 part number cl no. number of contacts weight rohs a 20g yes 22.1 21g 21 22g yes weight rohs 24g rm15wtrzb-3pa() rm15wtrzb-4pa() rm15wtrzb-8pa() part number rm15wtrzb-10pa() 3 4 8 20.65 a 10 20.6 109-1677-3- cl no. 109-1678-6- 109-1679-9- 109-1680-8- 109-1681-0- 109-1682-3- 21g yes weight rohs 23g 21g 21g 21g 21g rm15wtrzb-2s() part number rm15wtrzb-3s() rm15wtrzb-4s() rm15wtrzb-8s() rm15wtrzb-10s() rm15wtrzb-12s() 2 21.75 number of contacts a 3 22.1 4 21.75 8 21.6 10 21.6 12 21.6 receptacles (square flange) waterproof (when mated with corresponding plug) waterproof (single body) [specification number] (**), -** (71) : silver plated contacts (72) : gold plated contacts [specification number] (**), -** (71) : silver plated contacts (72) : gold plated contacts (shown one example) (shown one example) the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
8 b plug -- disassembly / assembly 5. 4. 3. 2. 1. disassembly 1 fix the plug in the assembly fixture (rm15tp-t01 (cl150-0098-0)), then remove the insulator body (p) and the back shell. right-angle plugs have set screws in the tightening ring at 2 locations. loosen the set screws before removing the back shell. 2 remove the 2 screws of the strain relief clamp, and then remove the clamp from the tightening collar. part name number of contacts 3 2,4,8,10,12 3 2,4,8,10,12 10,12 a 6mm 3mm 6mm 3mm 3mm b 21mm 21mm 12mm 12mm 25mm cable jacket cable wires conductors b a 3 min strain relief clamp back shell coupling tightening collar washer bushing insulator body (p) contacts clamp screw cable set screw(2) back shell tightening ring wiring 1 assure that the cable outer diameter will fit the strain relief clamp, and is prepared as recommended in table 1. it is recommended that the exposed conductors be pre-soldered, to assure easier insertion in the soldering cup. 2 pass the parts over the cable in the order of: tightening collar, washer, bushing, back shell, and coupling. refer to the draw ings (above) for assembly orientation of all components. 3 solder the wires to the contacts of the insulator body (p). use of heat-shrink tubing or another insulating media between the soldered contacts is suggested. connector assembly straight plugs 1 place the completely wired insulator body (p) in the assembly fixture secured in a vise. insert in the coupling, then back shel l. the back shell should be tightened to a torque of 3 n?m. right-angle plugs 1 place the completely wired insulator body (p) in an assembly fixture secured by a vise. insert in the coupling, then back shell (with tightening ring). when attaching the back shell, orient the cable in the desired direction and fasten the tightening ring to th e insulator body (p) with a torque of 3 n?m. after this, tighten and fix the 2 sets crews with a torque of 0.2 to 0.3 n?m. additional assembly recommendations: in applications where continuous extremely high vibrations may be encountered it is recommended that a thread locking compound be applied to male threads prior to assembly (loctite 271 ? manufactured by henkel japan k.k. or equivalent) waterproof verification - plug assembly apply air pressure of 17.6 kpa for 30 seconds from the mating side of the plug assembly. there shall not be any air leakage fro m inside the connector when submerged in the water tank. precautions 1 follow the correct assembly sequence, cable preparation and tightening torques. 2 assure that the applicable cable outer surfaces are free of scratches, oil, grease or any other contamination. 3 do not use excessive forces or improper tools when assembling or mounting the connectors. rm15wtpza- rm15wtpz- rm15wtlp- table 1 the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
9 b receptacle - recommended panel cut-outs b contact position arrangement and specifications b precautions 1. switch off the power of the circuit before disconnecting or plugging- in the connectors. 2. use a connectors with socket contacts at the power side of the circuit. 3. make sure that the coupling is in completely cocked position. 4. use correct plug / receptacle to assure dust and water protection. ?17 + 0.1 0 ?7.6 +0.1 0 front mounting, rear nut ?21 +0.1 0 ?19.65 +0.05 0 rear mounting, front nut 4-m30.5 ?24 +0.1 0 ?19.2 +0.1 0 20.60.05 20.60.05 1.40.05 square flange, screw mounting contact configuration shell size : 15 number of contacts withstanding voltage current rating insulation resistance contact resistance solder pot inner diameter 2 1800v ac / 1 minute 10a 1000m? min. 2m? max. 1.7mm 3 2000v ac / 1 minute 10a 1000m? min. 2m? max. 2.8mm 4 1500v ac / 1 minute 10a 1000m? min. 2m? max. 1.7mm 8 1500v ac / 1 minute 5a 1000m? min. 4m? max. 1.1mm 10 1000v ac / 1 minute 5a 1000m? min. 4m? max. 1.1mm 12 1000v ac / 1 minute 5a 1000m? min. 4m? max. 1.1mm panel thickness: 0.5 to 2 mm for rm15wtrz receptacles panel thickness: 0.5 to 2.5 mm for rm15wtrza receptacles panel thickness: 2.5 to 4 mm for rm15wtrzb receptacles notes : 1. when attaching the receptacle to the panel, be certain to check that the gasket is in place in the groove. do not pi nch the gasket. notes : 2. the view of the above diagrams is from the receptacle mating side. notes : 3. the symbol in the above diagrams indicates the coupling guide position of the receptacles. notes : 1. the contact configuration as viewed from the wiring side. notes : 2. the symbol in the above diagrams indicates the coupling guide position of the receptacles. notes : 3. withstanding voltages indicate test voltage values. the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
10 4 m ? max. 1000 m ? min no flashover or insulation breakdown. no electrical discontinuity for 10s max. no electrical discontinuity for 10s max. 8 m ? max. insulation resistance: 100 m ? min. insulation resistance: 100 m ? min. (dray state) 0when mated with corresponding connector. 1a dc 500v dc 1800v ac/one minute (4 pos.) 1500v ac/one minute (15, 31, 55 pos.) 1000v ac/one minute (20 pos.) frequency: 10 to 55hz, single amplitude of 0.75mm,for 3 hours in 3 axis. acceleration of 490m/s 2 , 11ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. 2000 cycles temperature : -55? ? room temperature ? +85? ? room temperature time : 30 ? 10 to 15 ? 30 ? 10 to 15 (minutes) 5 cycles 96 hours at temperature 0f 40? and humidity 0f 90% to 95%. complete dust protection. no water penetration when submerged for 48 hours at the depth of 1.8 meter. 1. contact resistance 2. insulation resistance 3. withstanding voltage 4. vibration 5. shock 6. durability (insertion/withdrawal) 7. temperature cycle 8. humidity 9. water / dust protection rating voltage rating current rating operating temperature range (note 1) storage temperature range (note 2) 600v ac, 840v dc (40 pos.) 500v ac, 700v dc (15, 31, 55 pos.) 350v ac, 490v dc (20 pos.) 5a -25? to +85? -25? to +85? product specifications (rm21wt to rm31wt size products) materials characteristic specification conditions body insulator contacts gasket brass diallyl phthalate brass, copper alloy chloroprene rubber or sir chrome plated or nickel plated color: black silver plated or gold plated color: black ------------------- ul94v-0 ------------------- ------------------- item material finish remarks note 1: includes temperature rise caused by the current flow. note 2: the term storage refers to products stored for long period of time prior to mounting and use. operating temperature r ange and humidity range note 2: covers non-conducting condition of installed connectors in storage, shipment or during transportation. note: do not mix different contact plating. ordering information rm 21 w t p * * * * - 2 p ( * * * * ) 1 2 1 3 4 5 6 7 series name : rm-w shell size lock type t : screw lock connector type p : plug r : receptacle 1 number of contacts contact type p : male contact s : female contact plating (71) : silver plated (72) : gold plated 5 6 2 3 4 7 rm 21 w t p - cp ( 10 ) ( * * * * ) 8 9 cp: strain relief 8 () with : external cable clamp () without : internal cable clamp 4~18 : cable size 9 the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
11 109-1860-0-71 109-1852-1-71 109-1855-0-71 plugs - straight, long back shell part number cl no. number of contacts ?a rm21wtps-15s(71) rm24wtpb-31s(71) rm24wtpb-31p(71) 15 31 31 21 24.3 24.3 ?b 32 36 36 c 49 54 54 d 23 26 26 e tm252 tm292 tm292 f m200.75 m240.75 m240.75 weight remarks rohs 104.5 144.6 140.0 silver plated only yes wrench opening dimension d 10 1 15 2 14 3 11 9 8 12 4 7 5 6 13 y z c f ?a ?b e (shown one example) ?b ?a e wrench opening dimension d c (shown one example) set screw ?a d c ?b e (shown one example) rm21wtps-15s(71) notes : 1. cable jacket diameter:use a 0.2mm. notes : 2. recommended set screw tightening torque : 0.2 to 0.3 n?m. notes : 3. when using the self-tightening strain relief verify the cable pull force requirements. notes : 1. cable jacket diameter:use a 0.2mm. notes : 2. recommended set screw tightening torque : 0.3 to 0.4 n?m. hrs recommended tool : pb205/1.27(cl 150-0066-3) applicable strain reliefs external cable clamp + internal, self-tightening internal, self tightening rm24wtp-cp14(71) rm21wtp-cp(8)(71) 114-2052-6-72 114-2053-9-72 114-2054-1-72 114-2055-4-72 114-2154-6-72 114-2056-7-72 109-1851-9-71 part number cl no. ?a jr16wcc-4(72) jr16wcc-6(72) jr16wcc-8(72) jr16wcc-10(72) jr16wcc-11(72) jr16wcc-12(72) rm24wtp-cp14(71) 0 4 0 6 0 8 10 11 12 14 ?b 23 23 23 23 23 23 29 c 17.5 17.5 17.5 17.5 17.5 17.5 17.5 d 21 21 21 21 21 21 26 e m200.75 m200.75 m200.75 m200.75 m200.75 m200.75 m240.75 weight 17.5g 17.5g 17.5g 17.5g 17.5g 17.5g 17.5g remarks rohs for rm21wt yes for rm24wt 109-1405-3-71 109-1406-6-71 109-1407-9-71 109-1493-0-71 109-1494-3-71 109-1495-6-71 109-1496-9-71 part number cl no. ?a rm21wtp-cp(8)(71) rm21wtp-cp(10)(71) rm21wtp-cp(12)(71) rm24wtp-cp(10)(71) rm24wtp-cp(12)(71) rm24wtp-cp(14)(71) rm24wtp-cp(16)(71) 0 8 10 12 10 12 14 16 ?b 23 23 23 27 27 27 27 c 38 38 38 38.5 38.5 38.5 38.5 d 7.5 7.5 7.5 8 8 8 8 e m200.75 m200.75 m200.75 m240.75 m240.75 m240.75 m240.75 weight remarks rohs 22.5 22.0 21.5 28.5 28.5 28.0 26.5 for rm21wt yes for rm24wt the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
12 109-1405-3-71 109-1406-6-71 109-1407-9-71 109-1493-0-71 109-1494-3-71 109-1495-6-71 109-1496-9-71 109-1575-3-71 109-1576-6-71 109-1579-4-71 109-1577-9-71 109-1578-1-71 part number cl no. ?a rm21wtp-cp(8)(71) rm21wtp-cp(10)(71) rm21wtp-cp(12)(71) rm24wtp-cp(10)(71) rm24wtp-cp(12)(71) rm24wtp-cp(14)(71) rm24wtp-cp(16)(71) rm31wtp-cp(10)(71) rm31wtp-cp(12)(71) rm31wtp-cp(14)(71) rm31wtp-cp(16)(71) rm31wtp-cp(18)(71) 0 8 10 12 10 12 14 16 10 12 14 16 18 ?b 23 23 23 27 27 27 27 31 31 31 31 31 c 38 38 38 38.5 38.5 38.5 38.5 42 42 42 42 42 d 7.5 7.5 7.5 8 8 8 8 12 12 12 12 12 e m200.75 m200.75 m200.75 m240.75 m240.75 m240.75 m240.75 m280.75 m280.75 m280.75 m280.75 m280.75 weight rohs 22.5 22 21.5 28.5 28.5 28.5 28.5 46 46 45 43.5 42 yes plugs - straight, short back shell d c ?a ?b e 14 13 9 8 7 65 4 3 2 1 10 15 11 12 y z set screw (shown one example) ?b ?a e wrench opening dimension d c (shown one example) set screw ?a d c ?b e (shown one example) rm21wtp-15s(71) notes : 1. cable jacket diameter:use a 0.2mm. notes : 2. recommended set screw tightening torque : 0.2 to 0.3 n?m. notes : 3. when using the self-tightening strain relief verify the cable pull force requirements. applicable strain reliefs external cable clamp + internal, self-tightening internal, self tightening rm24wtp-cp14(71) rm21wtp-cp(8)(71) 109-1401-2-71 109-1402-5-71 109-1403-8-71 109-1404-0-71 109-1491-5-71 109-1492-8-71 109-1571-2-71 109-1572-5-71 109-1573-8-71 109-1574-0-71 part number cl no. number of contacts ?a rm21wtp-15s(71) rm21wtp-20s(71) rm21wtp-15p(71) rm21wtp-20p(71) rm24wtp-31s(71) rm24wtp-31p(71) rm31wtp-40s(71) rm31wtp-55s(71) rm31wtp-40p(71) rm31wtp-55p(71) 15 20 15 20 31 31 40 55 40 55 21 21 21 21 24.3 24.3 30.8 30.8 30.8 30.8 ?b 32 32 32 32 36 36 42 42 42 42 c 37.5 37.5 37.5 37.5 44 44 52 52 52 52 e tm252 tm252 tm252 tm252 tm292 tm292 tm352 tm352 tm352 tm352 f m200.75 m200.75 m200.75 m200.75 m240.75 m240.75 m280.75 m280.75 m280.75 m280.75 weight remarks rohs 88.5 88.5 85 85 128 123 152 157 152 150 silver plated only yes 109-1478-7-71 109-1477-4-71 109-1851-9-71 part number cl no. ?a rm21wtp-cp10(71) RM21WTP-CP12(71) rm24wtp-cp14(71) 10 12 14 ?b 25 25 29 c 17 17 17.5 d 21 21 26 e rohs m200.75 m200.75 m240.75 yes notes : 1. cable jacket diameter:use a 0.2mm. notes : 2. recommended set screw tightening torque : 0.3 to 0.4 n?m. hrs recommended tool : pb205/1.27(cl 150-0066-3) notes : recommended set screw tightening torque : 0.2 to 0.3 n?m. the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
13 notes : recommended nut tightening torque : 3 n?m receptacles ?a cd 13 14 15 12 1 11 10 11 9 12 8 15 2 3 14 7 4 6 5 13 y z 10 1 2 3 9 8 4 7 5 6 y z e b f (shown one example) 20.62 6 tm252 tm252 4-?3.6 7 8 9 3 7 8 9 10 5 1 10 4 6 2 13 12 11 15 16 17 19 18 14 20 3 5 1 4 6 2 13 12 11 15 16 17 19 18 14 20 32 24 ?23.7 32 24 (shown one example) rm21wtr-15p(71) rm21wtrk-20p(71) waterproof (single body) notes : 1. screw size : m3 2. recommended nut tightening torque : 0.3 to 0.35 n?m 3. use a 1.9 to 2.0 mm dia.thick o-ring for the waterproof gasket that is used in the connector mounting portion. 109-1466-8-71 part number cl no. number of contacts remarks rohs rm21wtrk-20p(71) 20 gold plated only yes 109-1445-8-71 109-1447-3-71 109-1446-0-71 109-1448-6-71 109-1483-7-71 109-1484-0-71 109-1525-5-71 109-1527-0-71 109-1526-8-71 109-1528-3-71 part number cl no. number of contacts ?a b c d e rm21wtr-15p(71) rm21wtr-15s(71) rm21wtr-20p(71) rm21wtr-20s(71) rm24wtr-31p(71) rm24wtr-31s(71) rm31wtr-40p(71) rm31wtr-40s(71) rm31wtr-55p(71) rm31wtr-55s(71) 15 15 20 20 31 31 40 40 55 55 31 31 31 31 35 35 41 41 41 41 21 21 21 21 21 21 21 21 21 21 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 2 2 2 2 2.5 2.5 2.5 2.5 2.5 2.5 23.5 23.5 23.5 23.5 28 28 34 34 34 34 e tm252 tm252 tm252 tm252 tm292 tm292 tm352 tm352 tm352 tm352 weight remarks rohs 28 31.5 31.5 31.5 41.5 42 50 52 53.5 54 silver plated only yes front panel mount the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
14 ?a b rc 4Cm30.5 1.40.05 ?24 +0.1 0 ?280.1 240.05 240.05 notes : tolelance is +0.1/0. b receptacle - recommended panel cut-out b contact position arrangement and specifications b precautions square flange, screw mounting notes : 1. when attaching the receptacle to the panel, be certain to check that the gasket is in place in the groove. do not pi nch the gasket. notes : 2. the view of the above diagrams is from the receptacle mating side. notes : 3. the symbol in the above diagrams indicates the coupling guide position of the receptacles. notes : 1. the contact configuration as viewed from the wiring side. notes : 2. the symbol in the above diagrams indicates the coupling guide position of the receptacles. notes : 3. withstanding voltages indicate test voltage values. 1. switch off the power of the circuit before disconnecting or plugging- in the connectors. 2. use a connectors with socket contacts at the power side of the circuit. 3. make sure that the coupling is in completely cocked position. 4. use correct plug / receptacle to assure dust and water protection. contact configuration number of contacts withstanding voltage current rating insulation resistance contact resistance solder pot inner diameter shell size : 31 15 1500v ac / 1 minute 5a 1000m? min. 4m? max. 1.1mm 20 1000v ac / 1 minute 5a 1000m? min. 4m? max. 1.1mm 31 1500v ac / 1 minute 5a 1000m? min. 4m? max. 1.1mm 40 1800v ac / 1 minute 5a 1000m? min. 4m? max. 1.1mm 55 1500v ac / 1 minute 5a 1000m? min. 4m? max. 1.1mm panel thickness: 0.5 to 2 mm for rm * * * * wtr receptacles panel thickness: 2.5 to 4 mm for rm21wtrk receptacles part number ?a b rc for rm21wtr for rm24wtr for rm31wtr 22.1 26.1 32.1 13.3 15.1 18.3 0.8 0.8 0.85 front mounting, rear nut 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 17 16 18 19 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 shell size : 24 shell size : 21 the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.
the product information in this catalog is for reference only. please request the engineering drawing for the most current and accurate design information. all non-rohs products have been discontinued, or will be discontinued soon. please check the products status on the hirose website rohs search at www.hirose-connectors.com, or contact your hirose sales representative.

▲Up To Search▲

Price & Availability of RM21WTP-CP12

	To Download RM21WTP-CP12 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .